Media Conversion GBIC/SFP Modules Transceivers Network Interface Cards & PCMCIA Adapters Managed Switches Unmanaged Switches Wireless Power over Ethernet Hubs & Repeaters Baluns & Cabling Connectors Patch Cords Power Over Ethernet Power Over Ethernet Managed Switches 24-port 10/100 Power Over Ethernet Layer 2 Remotely Managed Switch with (2) SFP Combo ports Features • 15.4 Watts of DC power per port • 24 ports with full PoE functionality • Enable/Disable POE function • Power limit by classification • Power limit by management power feeding priority • Legacy Power Signature Detection for unique   electrical signatures • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to   achieve the best possible mode of operation over a link. • Auto-MDIX on all ports • 12K Jumbo Frame support • True non-blocking switching • 8K MAC address table • Back pressure half-duplex • Flow control full-duplex • Store and forward switching architecture • 8.8 Gbps backplane • 384Kbytes memory buffer • Reporting Features       • Management: Web Management, Remote Management,         Virtual IP Stacking       • Firmware update: TFTP firmware upgrade       • System default: Restore function for system default       • Port Trunk: Supports IEEE802.3ad port trunk with link         aggregation control protocol (LACP). The trunk group up         to 2 and maximum trunk port member up to 2 ports.       • VLAN: Port Based VLAN; IEEE802.1Q Tag VLAN, VLAN ID         up to 4094; VLAN group up to 5       • Quality of Service: Support port based, Tag based and IPv4 ToS       • Class of Service: Per port supports 2 priority queues       • Spanning Tree: Supports IEEE802.1w rapid spanning tree and         compatible with IEEE 802.1d       • Port Mirror: Supports RX packet mirror       • IGMP: Supports IGMP V1, V2       • Broadcast Storm: Enable/Disable, 5%, 10%, 20%, 25% Product Number 1) MIL-SM2401MAF Port One (24) 10/100BASE-TX (RJ-45) [100 m/328 ft.] Port Two (2) SFP/RJ-45 Combo Port (SFP Default) Power Over Ethernet Wireless Products ShAir AccessG-Pro™ 802.11g Managed WAP/Bridge with PoE Cost-Effective, Enterprise-Class Wireless Solution Introducing MILAN’s new cost-effective, enterprise-class wireless access point. The ShAir AccessG-Pro™ AP/Bridge is a 2.4 GHz IEEE 802.11g wireless bridge that allows bridging of two or more wired LANs, to connect difficult-to-wire locations, and makes it possible for multiple buildings to share an Internet connection. The ShAir AccessG-Pro™ AP/Bridge has three operational modes: Access Point, Access Point/Bridge, and Client Mode. The Access Point/Bridge mode provides both Access Point and Bridging functionalities. The Bridging function is supported through Wireless Distribution System (WDS). The Client mode allows the ShAir AccessG Pro AP/Bridge to connect to other industry standard 802.11b/g access points providing a simple solution to wirelessly share network resources amongst a wired workgroup. In addition, the ShAir AccessG-Pro™ AP/Bridge integrates Power-over-Ethernet (PoE) technology that eliminates extra cable during deployment and can be powered up where electrical outlets are not available or cost prohibited. Robust Security The ShAir AccessG-Pro™ AP/Bridge supports enterprise-class wireless security features such as 64-bit or 128-bit key WEP wireless data encryption, IEEE 802.1x RADIUS Authentication, the new Wi-Fi Protected Access (WPA), disabled SSID broadcast, wireless client isolation, and MAC address filtering to block unauthorized wireless clients. In addition, the new ShAir AccessG-Pro™ AP/Bridge also provides multiple levels of protocol filtering (Ethernet, IP, TCP/UDP) to further ensure network security. Enterprise-Class Network Management To simplify and reduce IT staffs workload and mean time-to-repair, the new ShAir AccessG-Pro™ AP/Bridge offers extensive, enterprise-class management features. First of all, the web-based management interface makes configuring and managing the ShAir AccessG-Pro™ a snap. IT professionals can also use Telnet or TFTP to quickly and easily manage the device. In addition, the ShAir AccessG-Pro™ AP/Bridge supports SNMP allowing easy integration of your wireless LAN with your existing wired infrastructure. Above all, ShAir AccessG-Pro™ AP/Bridge comes with the ShAir Wireless Management Utility that allows users to remotely manage, configure, update, and monitor multiple ShAir AccessG-Pro™s simultaneously. These management features ease Network Administrators’ large-scale deployment or remote management problems. Outstanding Value With the high-value price point, feature-rich design, and enterprise-class management options, MILAN’s new ShAir AccessG-Pro™ AP/Bridge reduces IT work burdens and lowers Total Cost of Ownership, yields a high return on investment, and is ideal for delivering highly reliable, wireless voice, video, and data services over a single network infrastructure. Features • IEEE Compliance • Graphical User Interface: • Remote Management: • SNMP • Power over Ethernet • Security • Client Isolation • Client Association Control • Antenna Alignment Assistance • Universal Plug-n Play (UPnP) • AP Load Balancing Product Number 1) MIL-W2332G Description ShAir AccessG-Pro™ 802.11g Managed WAP/Bridge with PoE Power Over Ethernet Injectors & Splitters POE Injectors Best Way to Bring Power to Your Network MILAN by Transition's new EmPowered Ethernet™ Series Power over Ethernet solutions deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations. Our new PoE products provides organizations with affordable, easy-to-use solutions that enable them to migrate their network infrastructure to support a growing number of advanced cost-saving, performance enhancing applications, such as streamlining wireless, VOIP, Network IP camera deployments, and centralized power backup solutions. Whether on a factory floor or in an enterprise facility, running power to hard to reach locations with MILAN by Transition's Power over Ethernet solutions significantly reduce cabling and outlet requirements while providing the lowest total cost of ownership. IEEE802.3af Compliant MILAN by Transition's EmPowered Ethernet™ Series Power over Ethernet solutions are IEEE802.3af compliant, which means that you are ensured of the following when deploying MILAN by Transition's PoE Solutions: • Legacy Installation - ensures safe delivery of power to   existing legacy devices as well as power-enabled terminals. • Preservation of Cabling Infrastructure - avoids altering existing   wiring and does not damage cabling infrastructure already in place. • Data Integrity - Power delivery over Ethernet cables does not   cause data degradation or loss of data integrity. Features • Ensures uninterrupted network operation by providing   a "power safe" path to the user • Intelligent detection process to detect Power over   Ethernet enabled terminals and protect legacy endpoints • Furnishes easy and cost-effective installation with fewer   cables and electrical outlets • 1U height and 19” Rack mountable (MIL-L800i only) • Provides one central secure location for power   (MIL-L800i & MIL-L100i) Product Number 1) MIL-L100i Description EmPowered Etherent™ Single-port Power over Ethernet Injector POE Injectors Best Way to Bring Power to Your Network MiLAN’s new EmPowered EthernetTM Series Power over Ethernet solutions deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations. MiLAN’s new PoE products provides organizations with affordable, easy-to-use solutions that enable them to migrate their network infrastructure to support a growing number of advanced cost-saving, performance enhancing applications, such as streamlining wireless, VOIP, Network IP camera deployments, and centralized power backup solutions. Whether on a factory floor or in an enterprise facility, running power to hard to reach locations with MiLAN’s Power over Ethernet solutions significantly reduce cabling and outlet requirements while providing the lowest total cost of ownership. IEEE802.3af Compliant MiLAN’s EmPowered EthernetTM Series Power over Ethernet solutions are IEEE802.3af compliant, which means that you are ensured of the following when deploying MiLAN’s PoE Solutions: • Legacy Installation - ensures safe delivery of power to   existing legacy devices as well as power-enabled terminals. • Preservation of Cabling Infrastructure - avoids altering   existing wiring and does not damage cabling infrastructure   already in place. • Data Integrity - Power delivery over Ethernet cables does   not cause data degradation or loss of data integrity. Product Number 2) MIL-L800i Description EmPowered Etherent™ 8-Port Power over Ethernet Injector Hub POE Splitter Best Way to Bring Power to Your Network MiLAN’s new EmPowered EthernetTM Series Power over Ethernet solutions deliver unified supply of data, voice, and video as well as electrical power through a single source by sending power over standard Category 5 and above twisted pair cables. Power over Ethernet simplifies installation and eliminates the need to run separate power cords and LAN cables to each Access Point or port locations. MiLAN’s new PoE products provides organizations with affordable, easy-to-use solutions that enable them to migrate their network infrastructure to support a growing number of advanced cost-saving, performance enhancing applications, such as streamlining wireless, VOIP, Network IP camera deployments, and centralized power backup solutions. Whether on a factory floor or in an enterprise facility, running power to hard to reach locations with MiLAN’s Power over Ethernet solutions significantly reduce cabling and outlet requirements while providing the lowest total cost of ownership. IEEE802.3af Compliant MiLAN’s EmPowered EthernetTM Series Power over Ethernet solutions are IEEE802.3af compliant, which means that you are ensured of the following when deploying MiLAN’s PoE Solutions: • Legacy Installation - ensures safe delivery of power   to existing legacy devices as well as power-enabled terminals. • Preservation of Cabling Infrastructure - avoids altering existing   wiring and does not damage cabling infrastructure already in place. • Data Integrity - Power delivery over Ethernet cables does not   cause data degradation or loss of data integrity. Features • Ensures uninterrupted network operation by providing a   "power safe" path to the user • Intelligent detection process to detect Power over Ethernet   enabled terminals and protect legacy endpoints • Furnishes easy and cost-effective installation with fewer   cables and electrical outlets • 1U height and 19” Rack mountable (MIL-L800i only) • Provides one central secure location for power   (MIL-L800i & MIL-L100i) Product Number 3) MIL-L100s Description EmPowered Etherent™ Single port Power over Ethernet Dual Voltage splitter (5v/12V) Power Over Ethernet Media Converters Power Over Ethernet Just Convert-IT™ 10/100BASE-TX to 100BASE-FX Stand-Alone Media Converters Enables enterprises to provide power to network devices over the existing CAT5 data connection. Transition's AC powered PoE media converters combine data received over a fiber optic link with -48VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that comply with the IEEE 802.3af™: 2003 standard. The converters also include a PD signature sensing and power monitoring features per the IEEE 802.3af standard. Other features include Over-Current Protection, Under-Current Detection and Fault Protection Input. The PoE converter is fully compatible with devices that comply with the IEEE 802.3af standard. The PoE converter is capable of inserting power on data pairs of the MDI. Features • External AC power supply • IEEE 802.3af Power Over Ethernet compatible • 48VDC PSE output voltage • Signal Pair Power Insertion • PD Detection Signature • Over-Current Protection • Under-Current Detection • Minimum Load Sensing • Fault Protection Input • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to achieve   the best possible mode of operation over a link. • AutoCross™   Automatically detects and configures the twisted pair port   on the converter to the correct MDI or MDI-X configuration. • Link Pass Through   Link Pass Through is a troubleshooting feature that allows   the media converter to monitor both the fiber and copper RX   ports for loss of signal. • Far End Fault (FEF)   A troubleshooting feature that is generally used in conjunction   with Link Pass Through to notify both end devices of a loss   of link. • Automatic Link Restoration   Transition Networks's converters will automatically   re-establish link in all network conditions. Product Number 1) J/POE-CF-01 2) J/POE-CF-01(SC) Port One 10/100BASE-TX (RJ-45) [100 m/328 ft.] 10/100BASE-TX (RJ-45) [100 m/328 ft.] Port Two 100BASE-FX 1300nm multimode (ST) [2 km/1.2 miles] 100BASE-FX 1300nm multimode (SC) [2 km/1.2 miles] Power Over Ethernet 10/100BASE-TX to 100BASE-FX Stand-Alone Media Converter Enables enterprises to provide power to network devices over the existing CAT5 data connection. Transition's AC powered PoE media converters combine data received over a fiber optic link with -48VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that comply with the IEEE802.3af™: 2003 standard. The converters also include a PD signature sensing and power monitoring features per the IEEE 802.3af standard. Other features include Over-Current Protection, Under-Current Detection and Fault Protection Input. This feature enhanced model offers the ability to enable/disable many of the features as well as force port capabilities (see switch section under Specifications). In addition, with the PSE/LPT switch enabled, a loss of Fiber RX will disable PSE power output on the UTP port for 2 seconds to allow remote device to re-initialize. The PoE converter is fully compatible with devices that comply with the IEEE802.3af standard. The PoE converter is capable of inserting power on data pairs of the MDI. Features • External AC power supply • IEEE 802.3af Power Over Ethernet compatible • 48 VDC PSE output voltage • Signal Pair Power Insertion • PD Detection Signature • Over-Current Protection & Under-Current Detection • Powered Device Reset • Minimum Load Sensing • Fault Protection Input • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to achieve   the best possible mode of operation over a link. • AutoCross™   Automatically detects and configures the twisted pair port   on the converter to the correct MDI or MDI-X configuration. • Link Pass Through   Link Pass Through is a troubleshooting feature that allows   the media converter to monitor both the fiber and copper RX   ports for loss of signal. • Far End Fault (FEF)   A troubleshooting feature that is generally used in conjunction   with Link Pass Through to notify both end devices of a loss   of link. • Automatic Link Restoration   Transition Networks's converters will automatically   re-establish link in all network conditions. Product Number 3) SPOEB1011-100 4) SPOEB1013-100 5) SPOEB1014-100 Port One 10/100BASE-TX (RJ-45) [100 m/328 ft.] 10/100BASE-TX (RJ-45) [100 m/328 ft.] 10/100BASE-TX (RJ-45) [100 m/328 ft.] Port Two 100BASE-FX 1300nm multimode (ST) [2 km/1.2 miles] 100BASE-FX 1300nm multimode (SC) [2 km/1.2 miles] 100BASE-FX 1310nm single mode (SC) [20 km/12.4 miles] Mini 10/100 Bridging 10/100BASE-TX to 100BASE-FX Mini Stand-Alone Media Converter The Mini Media Converters provide a cost-effective method for integrating fiber optic cabling into a 10/100 UTP environment. With its miniature size, the Mini offers a space saving alternative while it converts copper to fiber with the smallest footprint available in the industry. Depending upon the unit, this plug-and-play media converter offers three methods for powering the unit. All Mini's can be powered with the included power adapter, while other options include powering through a USB port or though an 802.3af Power over Ethernet enabled RJ-45 port. Two power options can be used simultaneously, providing the security of redundant power supplies. The Mini is available with either ST or SC fiber interfaces and is available for either multimode or single mode fiber. Features • Unit and Port LEDs allow for quick status information • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to achieve   the best possible mode of operation over a link. • Fixed Full-Duplex on fiber • AutoCross™   Automatically detects and configures the twisted pair port   on the converter to the correct MDI or MDI-X configuration. • Fixed Link Pass Through on POE and USB powered units • Automatic Link Restoration   Transition Networks's converters will automatically re-establish   link in all network conditions. • Far End Fault (FEF) (on all three versions)   A troubleshooting feature that is generally used in conjunction   with Link Pass Through to notify both end devices of a loss of link. ii) Standard Power Adapter and POE enabled option: Product Number 6) MP/E-PSW-FX-01 7) MP/E-PSW-FX-01(SC) 8) MP/E-PSW-FX-01(SM) Port One  10/100BASE-TX (RJ-45) [100 m/328 ft.] 10/100BASE-TX (RJ-45) [100 m/328 ft.] 10/100BASE-TX (RJ-45) [100 m/328 ft.] Port Two 100BASE-FX 1300nm multimode (ST) [2 km/1.2 miles] 100BASE-FX 1300nm multimode (SC) [2 km/1.2 miles] 100BASE-FX 1310nm single mode (SC) [20 km/12.4 miles] Power over Ethernet 100BASE-TX to 100BASE-FX Stand-Alone Media Converters Transition's AC or DC powered PoE media converters combine data received over a fiber optic link with -48VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that comply with the IEEE 802.3af standard. Other features include Over-Current Protection, Under-Current Detection and Fault Protection Input. SFEPE10xx-1xx products can operate in two modes: IEEE 802.3af mode as well as "legacy mode". In the IEEE 802.3af mode the POE is fully compatible with devices that comply with the IEEE 802.3af standard. The POE converter is also capable of inserting power on either the spare pairs or data pairs of the MDI. In the "legacy mode" POE can be configured for reverse polarity, 12 VDC, 24 VDC, or 48 VDC power insertion; as well as for other non-IEEE 802.3af compatible PDs. Different voltages & modes are switch selectable. Features • Internal AC or DC power supply • IEEE 802.3af Power Over Ethernet Compatible Mode • Legacy Mode (Non IEEE 802.3af) • 12, 24, or 48 VDC PSE Output Voltage with Reverse Polarity Selection • Signal Pair and Spare Pair Power Insertion • Over-Current Protection • Under-Current Protection • Minimum Load Sensing • Fault Protection Input • Exceeds IEEE 802.3af ripple requirements on PSE MDI power leads • Max 16.8 Watts Power output capacity at 48 VDC • PSE MDI Power Enable/Disable • AutoCross™   Automatically detects and configures the twisted pair port   on the converter to the correct MDI or MDI-X configuration. • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to achieve   the best possible mode of operation over a link. • Link Pass Through   Link Pass Through is a troubleshooting feature that allows the   media converter to monitor both the fiber and copper RX ports   for loss of signal. • Pause (IEEE 802.3xy)   Pause signaling is an IEEE feature that temporarily suspends   data transmission between two devices in the event that one   of the devices becomes overwhelmed. • Far End Fault (FEF)   A troubleshooting feature that is generally used in conjunction   with Link Pass Through to notify both end devices of a loss   of link. • Automatic Link Restoration   Transition Networks's converters will automatically re-establish   link in all network conditions. Product Number 9) SFEPE1011-100 10) SFEPE1013-100 11) SFEPE1014-100 Port One 100BASE-TX (RJ-45) [100 m/328 ft.] 100BASE-TX (RJ-45) [100 m/328 ft.] 100BASE-TX (RJ-45) [100 m/328 ft.] Port Two 100BASE-FX 1300nm multimode (ST) [2 km/1.2 miles] 100BASE-FX 1300nm multimode (SC) [2 km/1.2 miles] 100BASE-FX 1310nm single mode (SC) [20 km/12.4 miles] Power over Ethernet 10BASE-T to 10BASE-FL Stand-Alone Media Converters Enables enterprises to power network devices directly over the existing CAT5 data connection. The Power over Ethernet (POE) converter emulates IEEE 802.3af™ Power Sourcing Equipment (PSE), and is compatible with Powered Devices (PD) that comply with the draft IEEE 802.3af™ standard. The Power over Ethernet (POE) converter will detect the presence of a device that needs power and inject the applicable current into the data cable. Attractive solution for delivering power over CAT5 to powered devices such as access points, Voice over IP (VoIP) products, access servers, outdoor routers, and internet kiosks. Features • 48VDC input power supply • -48VDC output per port • 12W max load • Overload protection • PD Auto-sensing • Enable/Disable power MDI • Auto-Negotiation (802.3u)   Allows devices to perform automatic configuration to achieve   the best possible mode of operation over a link. • Link Pass Through   Link Pass Through is a troubleshooting feature that allows   the media converter to monitor both the fiber and copper RX   ports for loss of signal. Product Number 12) SEPOE1011-150 13) SEPOE1013-150 Port One 10BASE-T (RJ-45) [100 m/328 ft.] 10BASE-T (RJ-45) [100 m/328 ft.] Port Two 10BASE-FL 850nm multimode (ST) [2 km/1.2 miles] 10BASE-FL 850nm multimode (SC) [2 km/1.2 miles] For additional information, options and pricing about our ThinkCP™ products, please contact our sales representatives - (800)726-2477 or email - SalesDesk AT ThinkCP.com Copyright © 1997 - 2009 H. Co. Computer Products. All Rights Reserved. ThinkCP™ and H. Co. Computer Products™ are trademarks or registered trademarks of H. Co. Computer Products, Inc. For additional information regarding our trademarks, please visit Trademark Info at http://www.ThinkCP.com. This list is not intended to be an all-inclusive or comprehensive list of all H. Co. Computer Products trademarks and/or intellectual properties. Other product names used herein are for identification purposes only and may be the respective property or trademarks of other companies.